How To Reset Blink Camera And Sync Modules Everyone Need To Know?

Restarting the device is always the first step in solving any kind of problem with a piece of technology, and the same is true for Blink cameras. The fact that Blink cameras connect to a hub known as the Sync Module

You can reset a Blink camera by holding down the button on the side of the Sync Module until its light goes red. This will reset the Blink camera system, but you will need to reinstall the module via the Blink app before you can use the camera again.

As the Blink Mini camera does not need a Sync Module to function, it also includes a reset button on its body.

It is common practice to simply power cycle your internet router or Sync Module to get your Blink camera back online if it has been disconnected from the internet.

Throughout the troubleshooting process, it may save you a lot of time if you are aware of when it is necessary to reset your Blink system and when it is sufficient to just power cycle your router and module.

Resetting Your Blink Camera

To function, the Blink Indoor, Outdoor, XT, and XT2 cameras need to be paired with a Sync Module. The Sync Module links all your cameras to the Internet. In light of this, rather than resetting a single camera, it is often more effective to reset the whole system by pressing the reset button that is located on the Sync Module.

But rather than resetting your whole Blink system, there is a far easier option that can fix many of these problems: To do a power cycle on your Internet modem and/or Sync Module, just disconnect them and then plug them back in.

When is the proper time to restart my blink camera?

We strongly suggest attempting to power cycle your camera or Sync Module before resorting to resetting it if any of these devices have gone offline. Cycling the power supply is a straightforward initial step to take, and it does not require you to change your system in any way.

If you’re having trouble accessing your Blink camera system online, try restarting your Internet modem. This may be accomplished by following these steps:

• Turn off both your Internet modem and your wireless router and unplug them.
• Wait one minute.
• Reconnect the modem to the computer.
• When the modem has been brought back online, you should plug in the router.

Checking the lights on the Sync Module will allow you to determine whether or not the Internet power cycle was successful. There should be one completely green light and one completely blue light.

If this does not resolve the issue, try restarting the module.

• Pull the power line out of the Sync Module.
• Please hold on for at least 10 seconds.
• Connect it once again.
• For a minimum of one minute, wait for the system to begin operating normally again. Keep an eye out for the green and solid blue lights.
• Doing a factory reset on the Sync Module

Certain problems cannot be fixed by just cycling the power. In such a scenario, you will need to reset the Sync Module on your Blink system for it to function properly again.

To reset the module, you will need to press and hold the reset button that is located on the side of the device, right next to the USB port, until the light goes red. This might take anything from 15 to 30 seconds. When you see one steady green light and one flickering blue light, you will know that the reset was completed successfully.

This method of resetting the Sync Module will put it in the “setup mode” of its operation. There will be a loss of connection for all cameras. You will need to uninstall the Sync Module in the Blink app and then reinstall it before you can utilize your cameras again.

To remove and restore your Sync Module, please follow these steps:

• To get help using the Blink app, choose the question mark (?) icon.
• Choose “Remove Sync Module.”
• Scan the module’s serial number or input it manually.
• Press “Delete.”
• Return to the home screen, and then click the plus symbol that’s there.
• Choose “Blink wireless camera system” from the drop-down menu.
• Repeat the process of scanning or entering the module’s serial number.
• Choose the Blink system you have.
• Choose “Discover Device” from the menu.
• Just hit the “Join” button.
• Click the “Done” button.
• If resetting the Sync Module does not fix the problem with your camera, you should get in touch with Blink customer care for further assistance.

Resetting Blink Mini Cameras

It is not necessary to have a sync module attached for the Blink Mini to function. You will need to reset the camera itself if you are using a Blink Mini that functions independently.

At the very bottom of the camera is a button that may be used to reset the device. If your camera is not currently linked to the Internet or if you wish to connect it to a Sync Module, you will need to use the reset button.

You may either restart the Mini by cycling its power supply, or you can uninstall it from the Blink app and then reinstall it exactly like you would the Sync Module.

https://www.youtube.com/watch?v=eLITbjaC2eM

Methods for Resetting the Sync Module

If rebooting the device doesn’t solve the issue, try the following: By quickly resetting the Sync Module, your Blink camera system may start up again. On the back of the sync module is a physical reset button.

It is recommended that you attempt a power cycle before using this button to enter setup mode on your Sync Module (unplug and plug in the power cord). If you choose to reset your system, it will remain offline while you make the necessary adjustments to your sync module.

If the device’s blue blinking light and green steady light are both on, it has been reset successfully.

Hint: Sync module performance may be maximized by performing a reset before and after connecting it. Use a paperclip or a tiny screwdriver to reset the device.

A toy that goes “blink, blink”

when the Sync Module is reset to factory settings. This will render all cameras inoperable until they are reinstalled. Fundamentally, the system has to be adjusted.

After you’ve deleted the Sync Module from the Blink app and reinstalled it, you’ll be able to see your cameras again.

https://www.smarthomelivinginsider.com/1493-2which-connection-is-better-hdmi-arc-or-optical/

Here’s how to uninstall your Sync Module and reinstall it:

• When the Blink app has opened, you may access its help menu by clicking the icon.
• Get rid of “Sync Module” in the menu.
• The serial number of the module may be scanned or entered, and then “Delete” can be tapped.
• When you go back to the main menu, look for the + symbol to add the system.
• The “Blink wireless camera system” option is the one to go with.
• It is necessary to retry scanning or entering the module’s serial number.
• After selecting your Blink system, click the “Find Device” button.
• Choose your Blink system, and then click “Find Device.”

What Does Pressing the Reset Button on the Blink Camera Do?

You shouldn’t use this button to put your Sync Module into setup mode unless you’ve tried cycling the power on and off first (unplug and plug in the power cord).

If you choose the Reset option, your system will remain offline until you make the necessary adjustments to the settings on your Sync Module. That will not result in the camera having to restart.

The physical reset button on the device won’t be able to do the following:

• Remove the blink camera from the system or account in question.
• Get rid of the photo that’s sized like a thumbnail.
• Reset the settings of the camera to their original factory defaults.

How can I reset my Blink camera from a remote location?

With the Blink app, you will be able to remotely reset both the system and the cameras. On the other hand, the Sync Module has to have a physical reset performed on it.

Conclusion

It is possible to reset the Blink camera system; however, in most cases, it is not required to do so. If you are having problems with your Blink camera, the first thing you should do is attempt power cycling your Internet modem, and then try power cycling your Sync Module.

If this does not work, you may reset the Sync Module by pushing the reset button that is located on the side of the device. You will need to uninstall the Sync Module in the Blink app and then reinstall it after doing a reset; thus, you should always attempt power cycling before performing a reset.

If you do not have a Sync Module for your Blink Mini camera, you may reset the camera by pressing the reset button that is located on the bottom of the camera.